DAQ VXI-SC-1102 Bedienerhandbuch Seite 96
- Seite / 151
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 14 SCXI Hardware
DAQ Hardware Overview Guide 14-22 www.ni.com
cannot read the temperature sensor on the SCXI-1320 terminal block
if the SCXI-1320 is in the DTEMP configuration.
• The SCXI-1121 module drives analog input channels 0 to 3, even if you
are operating the module in multiplexed mode. In addition, if the
temperature sensor on the terminal block is in the DTEMP
configuration, the SCXI-1121 also drives analog input channel 4. The
SCXI-1200 cannot read the temperature sensor in DTEMP mode
because it reads all analog voltages off the analog lines of the SCXIbus
backplane.
• The SCXI-1122 module drives analog input channel 0 of the DAQ
device; if you use the SCXI-1300 terminal block with the temperature
sensor in the DTEMP configuration, the SCXI-1122 also drives analog
input channel 1. The SCXI-1200 cannot read the temperature sensor in
DTEMP mode because it reads all analog voltages off the analog lines
of the SCXIbus backplane.
• The SCXI-1140 module drives analog input channels 0 to 7, even if you
are operating the module in multiplexed mode.
• The SCXI-1141, SCXI-1142, and SCXI-1143 modules drive analog
input channels 0 to 7, even if you are operating the module in
multiplexed mode.
DIO-24 and the DIO-96
The DIO-24 and DIO-96 digital I/O devices work with the digital modules
and analog output modules. It is important to remember that when a digital
I/O device is cabled to an SCXI module, some of the device I/O pins, and
therefore some of the device resources, are reserved for SCXI use. SCXI
reserves the following DIO-24 and DIO-96 resources when cabled to a
digital or analog output module in multiplexed mode:
• DIO-24 digital I/O lines PB0 to PB3 and the DIO-96 digital output
lines APB0 to APB3 are the output communication lines to SCXI.
The entire port is reserved by NI-DAQ.
• DIO-24 digital I/O line PA0 and DIO-96 digital I/O line APA0 are the
input communication lines from SCXI. The remaining lines of these
ports are available only for input.
When you cable a DIO-24 to an SCXI-1162, SCXI-1162HV, SCXI-1163,
or SCXI-1163R in parallel mode, the 24 digital lines on the DIO-24 are
directly connected to channels 0 through 23 on the module; you cannot
access channels 24 to 31 on the module in parallel mode with a DIO-24.
- DAQ Hardware Overview 1
- Important Information 3
- Chapter 14 7
- SCXI Hardware 7
- Glossary 10
- Contents 11
- About This Guide 12
- MIO and AI Device Terminology 15
- Table 1 16
- Related Documentation 17
- MIO and AI Devices 18
- Chapter 1 MIO and AI Devices 19
- E Series Data Acquisition 20
- Set_DAQ_Device_Info 22
- MIO Device Analog Output 24
- E Series Digital I/O 26
- E Series PFI Pins 27
- Lab and 1200 Devices 28
- AI_Trigger_Config.vi 31
- DAQ_StopTrigger_Config 31
- Table 2-2 32
- Lab and 1200 Devices Groups 33
- Figure 2-1 34
- 1200 Device Acquisition Rate 35
- 1200 Device Calibration 36
- LPM Devices 37
- DAQ_Config 38
- LPM Device Digital I/O 39
- LPM Device Counter/Timers 40
- 516 Devices and 41
- DAQCard-500/700 Devices 41
- DAQ_Config. If you do 43
- Counter/Timer Operation 44
- Figure 4-2 45
- AT-AO-6/10 Analog 46
- Output Devices 46
- AT-AO-6/10 Digital I/O 48
- 6703/6704 Devices 49
- PC-TIO-10 Timing I/O Device 50
- PC-TIO-10 Counter/Timers 54
- PC-TIO-10 Digital I/O 55
- DIO-96 Digital I/O Devices 56
- DIO-96 Groups 57
- DIO-24 (6503) 58
- AT-MIO-16DE-10, and 6025E 58
- DIO-32F and 6533 60
- Digital I/O Devices 60
- Digital_Buffer_Write.vi) 62
- AMUX-64T External 63
- Multiplexer Accessory 63
- Table 11-2 64
- AMUX-64T Channel Numbers 64
- SCAN_Setup or 65
- MIO_Config 67
- Accessories 68
- SC-2042-RTD Accessory 69
- SC-2043-SG Accessory 69
- SCC Series Modules 70
- SCC-CI20 Current Input Module 72
- SCC-LP Lowpass Filter Modules 73
- SCC Configuration 74
- SCXI Operating Modes 76
- Chapter 14 SCXI Hardware 77
- SCXI Data Acquisition Device 80
- SCXI-1200 80
- SCXI Analog Input Modules 81
- SCXI-1100 81
- SCXI-1101 82
- SCXI-1104/C 83
- SCXI-1112 83
- SCXI_Scale function to 84
- SCXI_Single_Chan_Setup 84
- SCXI-1125 85
- SCXI-1122 85
- SCXI-1126 86
- SCXI-1127 87
- SCXI-1140 87
- SCXI Analog Output Module 89
- SCXI-1124 89
- SCXI Digital Modules 90
- SCXI-1160 and SCXI-1161 90
- SCXI-1162 and SCXI-1162HV 91
- SCXI-1163 and SCXI-1163R 91
- SCXI-1530, SCXI-1531 92
- SCXI-1540 92
- SCXI_Track_Hold_Setup 94
- DIO-24 and the DIO-96 96
- DIO-32F and 6533 Device 97
- VXI-DAQ Devices 99
- AO_Change_Parameter or the 100
- Multifunction VXIbus Devices 101
- VXI-DAQ Signal Conditioning 102
- VXI-SC-1102 Submodule 103
- VXI-SC-1150 Submodule 103
- PXI DAQ Devices 104
- PXI DAQ Signal Conditioning 105
- NI 5411 Devices 106
- Chapter 17 NI 5411 Devices 107
- DDS Mode 108
- Table 17-2 110
- NI 5411 Operational Modes 110
- Device Analog Input 112
- Data Acquisition 113
- Acquisition Timing 114
- Current Source 115
- Digital I/O 115
- Device Input 116
- Chapter 19 NI 40XX Devices 118
- DSA Devices 119
- and NI 455 120
- Analog Input Channels 120
- Data Acquisition Timing 121
- Channels 122
- Digital I/O 123
- Counter/Timer Operation 124
- Devices 125
- Chapter 21 671X Devices 126
- Technical Support Resources 129
- Worldwide Support 130
- Numbers/Symbols 131
Verwandte Produkte und Handbücher für Audioverstärker DAQ VXI-SC-1102
Audioverstärker DAQ VXI-SC-1102 Bedienungsanleitung
(209 Seiten)
(209 Seiten)
Audioverstärker DAQ VXI-SC-1102 Bedienerhandbuch
(323 Seiten)
(323 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern